Navigation
News
GoldCoastCB Forum -- May 26, 2018, 08:17:23 PM
Pages: [1]   Go Down
Print
Author Topic: Toenail polisher upgrade  (Read 209 times)
0 Members and 1 Guest are viewing this topic.
number7
*****
Online Online

Posts: 548



« on: April 25, 2018, 01:00:31 PM »

You may remember the cordless polisher I bought from the  Commies are banned some time ago
Seemed like a good idea at the time - I was hoping to polish cars with it
but it was only ever good enough to keep my toenails smooth and shiny confused2
Then the battery failed (after only a few charge cycles) so I threw it in the corner and got refunded.

Yesterday I really needed shiny nails so I decided to get the machine out and try it again.
I hoped I could run it wired directly to the charger but it didnt work - not enough amps...

My new design is much better - it spins a bit fast but its now good enough to polish
 Starvin Dimmock       Boobs    and my toenails without the battery going flat   icon_thumright


http://i67.tinypic.com/24zzx2p.jpg


[attachment deleted by admin]
Logged
number7
*****
Online Online

Posts: 548



« Reply #1 on: April 25, 2018, 01:06:57 PM »

hey  munky2
when you drag ur hairy arse out of bed could you help with the previous post?
the attachment wont work - same pic I sent you last night via mms
I took another shot that is smaller but still wont show up here
Logged
admin_monkey
admin bloke
*
Offline Offline

Gender: Male
Posts: 40


i is monkey


« Reply #2 on: April 25, 2018, 04:00:18 PM »

what a relief, i though yellow toe nails where going to be in the pic

bit of a monkey wiring job there  munky2
Logged

humans piss me off.
number7
*****
Online Online

Posts: 548



« Reply #3 on: April 25, 2018, 04:15:30 PM »

 Tears  you should see the inside.....

Im not sure how long the 4v electric motor will last now its getting a solid 12v   dontknow

So im looking for a 12v battery with a dead cell (-2.2v) making about 10v power source might slow it down
or some sort of voltage resistor in the wiring...   walk
Logged
cOOter
*****
Offline Offline

Gender: Male
Posts: 1676



WWW
« Reply #4 on: April 25, 2018, 07:33:37 PM »

4v electric motor.....its getting a solid 12v

4 into 12?  Crazy keep the bearing-bushes lubed real goodly.

all that fucking around just to buff fungus off your feet?

soak 'em in warm salty water for 15 minutes, then run around the block ... all the fungus will fling off onto the neighbors front yard and three legged pregnant cat.

 Russell Coight

Logged
number7
*****
Online Online

Posts: 548



« Reply #5 on: April 30, 2018, 06:23:04 PM »



 Tears  can you see the problem?   Tears

I already threw this in the rubbish today but thought I would try open it up for a look

***BEWARE!!!***    director

a simple twist of the cable could lead to deadly circumstances...

Why   Commies are banned  why???

Logged
cOOter
*****
Offline Offline

Gender: Male
Posts: 1676



WWW
« Reply #6 on: April 30, 2018, 07:27:56 PM »

deadly? the three hair thickness wires were so thin they'd melt before catching on fire. Crazy

just re wire with some man sized wire, and glue the plate back on...

... or did you butcher it when taking it off?  Russell Coight
Logged
number7
*****
Online Online

Posts: 548



« Reply #7 on: April 30, 2018, 07:51:03 PM »

nah it came off ok but will need to be glued back on
I think when I untwist the wires it will still work -
they didnt get that hot due to tiny current draw even with a dead short    confused2
Logged
cOOter
*****
Offline Offline

Gender: Male
Posts: 1676



WWW
« Reply #8 on: April 30, 2018, 10:39:16 PM »

Looks like only a 3 pin transistor on that circuit board.
It (the trannie) showed 8v on the 15v drill battery I used to test them, so is about right and working for a 7.2v gayogag.

I'd remove the curly cords on both and soldier in some new thicker wire that will handle the PTT drain amps better and not twist in the case.

Heat sink on the transistors would be good as well but I don't think there's much room in the case for anything but some alloy foil (wrapped length ways) around  the black square part of the trannie.

I just made love to a Cool Chicken
Logged
admin_monkey
admin bloke
*
Offline Offline

Gender: Male
Posts: 40


i is monkey


« Reply #9 on: April 30, 2018, 11:18:15 PM »

cooter you dumb human, the silver square box in the pics is the heat sink  munky2

some small drill holes on the outside to allow some air flow would be an idea.

i is monkey.

<a href="http://www.youtube.com/watch?v=J-SUoHmpRdM" target="_blank" class="aeva_link bbc_link new_win">http://www.youtube.com/watch?v=J-SUoHmpRdM</a>
Logged

humans piss me off.
number7
*****
Online Online

Posts: 548



« Reply #10 on: April 30, 2018, 11:31:42 PM »

ahh yes thanks  munky2 that is correct
the metal plate next to the pcb is the heat sink for the tranny

the board is glued down but all I can see is 2 capacitors and the 3 pin transistor - nothing to it  thebirdman
for $3.16 they cant be putting too many bits in it

think I will change the curly cable to a more manly type
this will act as transmitter power and the other 1 on the receive...   Deak Mic

back to polishing my toenails.... love1
Logged
Pages: [1]   Go Up
Print
 
Jump to:  

Anone designed by pixelslot.
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.189 seconds with 27 queries.